IR6000 ERROR CODE PDF

These are all list of error code in Canon iR/iR more to come, i hope your machines works fine and never get error. E Main cause. fixing oil, the error code is indicated. E The rated voltage of the power supply and that of the fixing unit do not match. E Clock pulses fail to be generated. canon ir is showing an error codes E How it will solve? Your error code is for the fixing unit solve by checking the follwoing: 1. Fixing lamp.

Author: Kigagor Moogunos
Country: Austria
Language: English (Spanish)
Genre: History
Published (Last): 24 April 2017
Pages: 26
PDF File Size: 18.75 Mb
ePub File Size: 11.17 Mb
ISBN: 611-8-23283-936-6
Downloads: 17780
Price: Free* [*Free Regsitration Required]
Uploader: Vozuru

The thermal switch TP1 has an open circuit. The fixing heater has an open circuit. The SSR is faulty.

Canon iR5000 Service Manual: Error Codes; List Of Error Codes

The main thermistor TH1 has a short circuit. The sub thermistor TH2 has detected overheating. The main thermistor TH1 has poor contact or an open circuit. The SSR has a short circuit. The fixing web has been taken up.

The fixing web length sensor PS45 is faulty.

After replacing the fixing web, be sure to reset the two web counters in service mode: The main motor M2 is faulty. The drum motor M1 is faulty. The waste toner feedscrew is faulty. The waste toner clock irr6000 MSW2 is faulty. The fixing motor M19 is faulty.

The hopper connector is left disconnected. The copy data controller or the remote diagnostic device is faulty. The main controller PCB is faulty. The laser shutter is faulty. The laser unit is faulty. The potential measurement PCB is faulty. The laser driver PCB isfaulty.

The wiring is faulty short circuit, open circuit. The laser scanner motor M15 is faulty. The wiring is faulty short circuit,open circuit. The controller cooling fan FM4 is faulty.

The scanner HP sensor PS39 is faulty. The scanner motor M3 is faulty.

The reader controller PCB is faulty. Caution No code is indicated, and keys are locked. The lamp inverter PCB is faulty. The scanning lamp xenon tube is faulty. The inverter Codf is faulty.

  CHOQUE DISTRIBUTIVO EN PEDIATRIA PDF

Error Code Canon IR error E

The main controller PCB. The hard disk drive is faulty. Main Cause The wiring is faulty short circuit, open circuit. The hard disk drive isfaulty. Main Cause The hard disk fan FM7 is faulty. The wiring is faulty short circuit, opencircuit. Main Cause The various printer board accessories are faulty. Mode ofDetection An error has occurred in the communication between the various. Main Cause The connector is not connected properly. The remote diagnostic device PCBis faulty.

The copy data controller PCB is faulty. The finisher controller PCB isfaulty. The ADF V power supply isfaulty. The reader controller PCB isfaulty. The finisher accessories powersupply PCB is faulty.

The finisher controller PCB is faulty.

The copy data controller orthe remote diagnostic device is faulty. Mode ofDetection The copy data controller or the NE controller is out of order or anopen circuit has been detected. The coin vendor is faulty. Mode of Detection The communication between the coin vendor and the main controllerPCB has been interrupted. Main cause The connector has poor contact.

Main cause The LAN card is faulty. The DC power supply fan FM6 is faulty. The feed fan FM1 isfaulty. The heat discharge fan FM3 is faulty. The primary charging assemblycooling fan FM2 is faulty. Mode ofDetection While the primary charging assembly cooling fan is being driven. Main Cause The cooling fan FM1 is faulty. Mode of Detection When the host machine’s power switch is turned on, the backupdata of the EEPROM cannot be read or the data, if read, has an error.

The communication line has an opencircuit. Mode ofDetection While the machine is in standby, the communication with the hostmachine has been interrupted for 5 secs or more. Mode ofDetection The communication between the host machine and the finisher hasbeen interrupted; this error is detected by the host machine.

Main Cause The height sensor PS1 is faulty. Mode ofDetection Communication between the height sensor and the finisher controllerPCB is not possible, or communication data has an error. The puncherdriver PCB is faulty.

Main Cause The delivery motor clock sensor PI10 is faulty. The delivery motor M2 is faulty. Mode ofDetection When operation starts, as many clocks as needed do not arrivefrom the delivery motor clock sensor.

  JAIME BAYLY EL HURACAN LLEVA TU NOMBRE PDF

Main Cause The alignment plate home position sensor PI6 is faulty. The alignmentmotor M3 is faulty. Mode ofDetection The alignment plate does not leave home position when the alignmentmotor has been driven for 2 secs. Main Cause The stapler home position detecting switch MS7 is faulty. The stapler motor M6 is faulty. Mode ofDetection The stapler does not leave home position when the stapler motorhas been driven for 0.

Main Cause The stapler shift home position sensor PI7 is faulty. The stapler shift motor M4 is faulty. Mode ofDetection The stapler unit does not leave home position when the stapler shiftmotor has been driven for 4 secs. Main Cause The swing motor clock sensor PI20 is faulty. The swing guide open sensor PI18 is faulty. The safety area switch MS3 is faulty. The swing guideclosed detecting switch 2 MS6 is faulty. The swing motor M7 is faulty. Mode ofDetection The swing guide closed detecting switch 2 does not turn on whenthe swing motor has been rotated CCW for 1 sec.

Main Cause The tray home position sensor PI8 is faulty. The tray upper limit detecting switch MS5 is faulty. The tray lifter motor M5 is faulty. Main Cause The shutter open sensor PI5 is faulty.

The safety area detecting switch MS3 is faulty. The shutter closed detecting switch MS4 is faulty. Mode ofDetection The shutter closed detecting switch does not turn on when the No. The punch motor M1P is faulty. The punch driver PCB is faulty. Mode ofDetection The puncher does not leave home position when the punch motorhas been driven for msecs.

The horizontalregistration motor M1P is faulty. Mode ofDetection The puncher does not leave home position when the horizontal registrationmotor has been driven for 4 secs. The paperpositioning plate motor M4S is faulty.