Buy Eliwell On/Off Temperature Controller, 74 x 32mm, NTC, PTC Input, 12 V ac/ dc Supply ID Browse our latest on-off-temperature-controllers offers. Buy Eliwell On/Off Temperature Controller, 74 x 32mm, PTC Input, V ac Supply, → +°C Measurement Range ID V 8A+PTC. Browse our. In order to configure the instrument for this purpose you must access the folder identified by the “Add” label and use the parameters “dEA” and “FAA”. ID LX.
|Published (Last):||10 August 2015|
|PDF File Size:||1.16 Mb|
|ePub File Size:||16.75 Mb|
|Price:||Free* [*Free Regsitration Required]|
Eliwell ID970 MC (Milk)
Users must not be able to access parts with dangerous voltage levels under normal operating conditions. Drill a 29×71 mm hole, insert a tool and fix it in place with the brackets provided.
The Setpoint value appears on the display. The programming parameters are downloaded when the device is switched on.
Eliwell ID MC (Milk) |
The relay contacts are voltage-free. Alarm fliwell time after instrument is switched on following a power failure. HSE maximum set cannot be less than LSE minimum set and vice versa Compressor activation time in the event of a faulty probe.
I970 reserves the right to make any changes or improvements without prior notice and at any time. Temperature value understood as distance from the Setpoint or as an absolute value based on Att which if exceeded in an upward direction triggers the activation of the alarm signal.
The parameter indicates that a protection is active on the relay actuations of the generic compressor. Defrost cycles can be controlled at time intervals. There are 2 operating modes determined by parameter AtP: Programming parameter transfer from instrument to Copy Card.
elidell Although Eliwell has taken all possible measures to guarantee the accuracy of this document, it declines any responsibility for any damage arising out of its use. The two sets are interdependent: Positive or negative temperature value added to the value read by probe Viewing mode during defrosting. In normal conditions, the labels for the Set point value is found in the menu.
Do not exceed the maximum current allowed. The device must be suitably protected from water and dust according to the specific application and only be accessible using special tools except for the front keypad.
It’s a community-based project which helps to repair anything.
The operation cannot be cancelled. View with decimal point. At the end of the lamp test, the following messages are displayed for about 5 seconds: The ID controllers are devices suitable for applications on normal or low temperature refrigerating units. Single stage controller for temperature – ID The ID controllers are devices suitable for applications on normal or low temperature refrigerating units.
Between the request and effective activation of the compressor relay, at least the specified time must elapse. At least the indicated time must elapse between switch-off of the compressor relay and the successive switch-on.
Set point setting folder; -Pb1: They are provided with a PTC thermostatic probe input NTC can be selected by parameter and two relay outputs for compressor and defrost management.
All the versions are provided with a TTL connection in order to use Copy Card, the quick programming accessory. ID A Single stage controller for temperature. Defrost counting is always active when the machine is on and starts at each power-on.
Description Technical Schema Description: The instrument has screw terminals for connecting electrical cables with a maximum diameter of 2. Delay time in activating the outputs after switch-on of the instrument or after a power failure. Always switch off machine before working on electrical connections. The indicated time must elapse between two subsequent switch-ons of the compressor.
Erasing all parameters in the key.
Single stage controller for temperature – ID – Eliwell France
In addition, the 16 A compressor relay options and the buzzer are provided. The password is enabled if the value of the PA1 parameter is not 0. The same applies to any person or company involved in preparing and writing this document. Programming parameter transfer from Copy Card to instrument. The sensor has no connection polarity and can be extended using an ordinary eljwell cable note that extending the probe may affect the electromagnetic compatibility EMC of the instrument: Make sure that the power voltage complies with the device voltage.
ID Single stage controller for temperature. Always make sure that the area next to the cooling openings of the tool is adequately eliqell. TTL for connection to Copy Card 3 outputs on relays: Single stage controller for temperature.
Any protection devices required to comply with product requirements or dictated by common sense due eoiwell obvious safety reasons should be installed externally.
The continuous improvement of our products can cause some variations in this non contractual document even without notice. ID LX Single stage controller for temperature. Do not assemble the instrument in excessively humid or dirty locations since it is designed to be used in locations with normal pollution levels.