Documents Similar To CINI Manual. Industrial Insulation Manual. Uploaded by. Haris Prawoto. Standard Specification for Hot Insulation (Piping & Equipment). This SPECIFICATION is based on the CINI Handbook “Insulation for Industries”, English. Version, dated 1st October (also known as the ” edition”). This section is based on the Committee Insulation Netherlands. Industry (CINI) Manual “Insulation for Industries”. DACE fol- lows the CINI standard as much as.

Author: Sasar Daira
Country: Oman
Language: English (Spanish)
Genre: Literature
Published (Last): 27 January 2015
Pages: 18
PDF File Size: 17.56 Mb
ePub File Size: 19.14 Mb
ISBN: 955-5-74032-251-6
Downloads: 34748
Price: Free* [*Free Regsitration Required]
Uploader: Mikakasa

September Page 1 of 12 Part 1 General 1. Supports shall be designed to withstand all service loads.

CINI Manual “Insulation for Industries”

The mechanical properties, such as compressive strengths, tensile strengths, shear strength and stress-strain behaviour etc.

The requirements for pipe material and installation in sewer and drainage collection systems.

The information set forth in these publications is provided to users for their consideration and decision to implement. The information in manuall CINI Manual is updated on an annual basis and adapted to the new developments in the market.

To use this website, you must agree to our Privacy Policyincluding cookie policy. If metal jacketing is used, sufficient space and drainage shall be provided to avoid internal accumulation of water caused by condensation, water vapour diffusion, capillary action and water ingress.

Circumferential joints between segments in adjacent lengths of pre-formed rigid insulation shall also be staggered. The Main Contractor is the party that carries out all or part of the design, engineering, procurement, installation and commissioning or management of a project.


What is Static Electricity? Cory Wilkerson 1 years ago Views: The heat gain heat ingress for piping in off-plot areas shall be determined by the Principal. Each line should be insulated separately; a common insulation cover should not enclose adjacent indjstries.

All material specifications have the same structure, with easy to find information. This type of insulation is often used in conjuction with heat industies.

Cini manual insulation for industries pdf – Google Docs

Life cycle costs calculations shall be carried out to arrive to the lowest cost, based on the service life of 20 years. Pressure vessel basics for all engineers by Sharjeel Aslam Faiz 1. The CINI Manual is updated on an annually basis, to include the latest developments and to maintain it as the state-of-the-art standard.

As an alternative non-contact insulation may be considered as indicated in Appendix 3 and 5. This standard is intended to provide useful information to the Professional Service Provider PSP to establish a basis of design. High quality pipe insulation. The jacketing selection has been changed. Cold insulation systems shall be vapour tight. If approved by the Principal, deviations shall be shown on the piping drawings.

Technical and industrial insulation. Its total thickness shall be as close as possible to the economic insulation thickness and shall be rounded off to the upper commercially available thickness.


For multi-layer systems, the half-pipe sections shall be factory-bonded into innsulation integral unit. These specifications may be used in whole or in part by any party without More information. The factory-assembled support shall have a insjlation extended multiplex vapour barrier with a sufficient overlap of 50 mm covered with a bonded 1.

The maximum stresses in the foam shall be limited to 0.


The copyright of this document is vested in these companies. White Paper June 24, Stilling Well Recommendations This document describes general requirements for stilling wells used for radar tank gauging applications. Ihdustries programs shall be used to determine the economic insulation thickness.

Alternative solutions for special cases may be submitted to the Principal for approval, e. Jansen, Peutz Consulting Engineers, The Netherlands, emphasise the need for an adequate pipe noise control procedure, with reference to the design phase, insulation More information.

The responsibility of the engineer is Fo information.

The insulation system and the materials selected shall comply with this DEP. Removable hot insulation around flanges, valves, etc.