Buy ASTM De1 Standard Test Method for Evaluating Degree of Blistering of Paints from SAI Global. 年1月20日 ASTM D() Standard Test Method for Evaluating Degree of Blistering of Paints_能源/化工_工程科技_专业资料。ASTM D(). This standard is issued under the fixed designation D ; the number immediately This test method is under the jurisdiction of ASTM Committee D01 on Paint.
|Published (Last):||23 December 2004|
|PDF File Size:||17.2 Mb|
|ePub File Size:||10.4 Mb|
|Price:||Free* [*Free Regsitration Required]|
Accelerated weathering resistance When tested in accordance with Paragraph 3.
ASTM D714 – 02(2017)
The test specimen shall be v714 at three locations on the panel that have a dry film thickness within the tolerance range for the coating process. Proceed to Checkout Continue Shopping. Table 2 on page s714 illustrates the various classifications for adhesion loss. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Abrasion resistance The coating film shall have a wear index of While primarily intended for use on metal and other nonporous surfaces, this test method may be used to evaluate blisters on porous surfaces, such as wood, if the size of blisters falls within the scope of these reference standards. Coatings covered by this standard include paints, stains, clear coats, and powder coats. This standard has been approved for use by agencies of the Department of Defense.
Please first verify your email before subscribing to alerts.
Need more than one copy? Originally approved in Rust grades Classification of adhesive test results.
This test method provides a standard procedure of describing the size and density of the blisters so that comparisons of severity can be made. Size distribution in terms of mensuration units, Frequency asmt occurrence per unit area, Pattern of distribution over the surface, and Shape of blister For the usual tests, an actual count is more elaborate than is necessary.
ASTM D() Standard Test Method for Evaluating Degree of Blistering of Paints_图文_百度文库
As the voice of the U. Identification marks shall be added to the specimen as required for control purposes. We have no amendments or corrections for this standard. General Scope These methods prescribe the procedures to be followed in the selection of material, chemical preparation, coating application, testing, and evaluation of factory applied finish coatings for steel doors and frames. Visual representations of the various degrees of blistering are shown in Figures 2 through 5 of this document.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Please first log in with a verified email before subscribing to alerts. NOTE 1—A quantitative physical description of blistering would include the following characteristics determined by actual count: Already Subscribed to this document.
It is preferable however, to use the original photographs or drawings when available. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. Visual reference for percentage of rust Blister size 2 Blister size 4 Blister size 6 Blister size 8 Photographic reference standard for degree of chalking.
Your Alert Profile lists the documents that will be monitored. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. The coated surface of the specimen shall not be handled or come in contact with other objects in such a aztm as to disrupt the coated surface.
This standard is also available to be included in Standards Subscriptions. Standards Subsctiption may be the perfect solution. These methods prescribe the procedures to be followed in the selection of material, chemical preparation, coating application, testing, and evaluation of factory applied finish coatings for steel doors and frames.
Asrm primarily intended for use on metal and other nonporous surfaces, this test method may be used to evaluate blisters on porous surfaces, such as wood, if the size of blisters falls within the scope of these reference standards. When the reference standards are used as a speci? Standard Test Method f Reference Standards for Blistering of Paint Coatings2 3.
Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Subscription pricing is determined by: The coating film shall have a wear index of Certification When reference is made to this specification the following statement shall be used: Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards.
You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. When axtm reference standards are used as a specification of performance, the permissible degree of blistering of the paint system shall be agreed upon by the purchaser and the seller.